Sometimes you just need a clean, steady sound at an exact pitch: to check a speaker, tune a guitar, find a rattle in a car door or hear where your own hearing tops out. This tone generator plays any frequency from 20 to 20,000 Hz, as a smooth sine wave or a brighter square, triangle or sawtooth, and lets you change it while it plays.
Everything happens in your browser. The sound is made on your own device, nothing is downloaded or uploaded, and there is no account. When you need the tone as a file, press Save as WAV and it is written straight to your computer.
How to play a tone
- Set the frequency. Drag the Frequency slider, type a number into the box beside Hz, or pick one of the common tones such as 440 Hz.
- Choose a wave: Sine, Square, Triangle or Sawtooth.
- Turn your speakers or headphones down, then press Play. The tone starts at 20% volume.
- Raise the Volume slider slowly until you hear it clearly. Change the frequency, the wave or the volume at any time: the tone follows.
- Press Stop when you are done.
The slider covers the range evenly by octave, so the low notes are as easy to reach as the high ones: 20 Hz sits at the far left, 2,000 Hz about two thirds of the way along and 20,000 Hz at the far right. For an exact value, type it in. The box takes decimals, such as 432.5, and pulls anything outside 20 to 20,000 Hz back into range when you leave it.
The buttons beside the box move the tone by 1 Hz or by a whole octave. An octave down halves the frequency and an octave up doubles it, which is handy for hearing the same note higher or lower.
Choosing the wave
Every wave plays at the frequency you set, but each one sounds different because of the extra, higher tones it carries. Pick the wave that suits the job.
| Wave | How it sounds | Good for |
|---|---|---|
| Sine | Pure and soft, a single pitch with nothing added | Speaker and hearing checks, tuning, testing a room |
| Square | Hollow and buzzy, like an old video game | Hearing a tone clearly on small speakers |
| Triangle | Between the two, gentler than square | A softer test tone that still stands out |
| Sawtooth | Bright and harsh, full of higher tones | Checking that a speaker handles a rich sound |
What people use a frequency generator for
A frequency generator is a simple tool with a surprising number of everyday uses.
- Testing speakers and headphones. Sweep the slider slowly from low to high and listen for rattles, buzzing or a range where the sound drops away. Low tones show how much bass a speaker can play.
- Tuning an instrument. Play 440 Hz, the A above middle C, and tune your A string to it. The page shows the nearest note for any frequency, and how many cents it is above or below.
- Checking your hearing range. The highest tones fade from hearing with age, so many adults cannot hear the top of the range at all. Start quietly and listen for where the tone fades out. This is a curiosity, not a hearing test: see a doctor or an audiologist if you are worried.
- Finding a rattle or a resonance. A slow sweep through the low notes makes a loose panel, shelf or car part buzz at its own frequency.
- Trying 432 Hz. Some musicians prefer tuning A to 432 Hz rather than 440 Hz. Press 432 Hz to hear the difference for yourself.
Before a call, a quick microphone test does for your microphone what a tone does for your speakers. Note that this page makes sound: it is not the wire tracer that electricians also call a tone generator.
Saving the tone as a WAV file
Under Save the tone as a WAV file, choose a Length of 1, 5, 10, 30 or 60 seconds, then press Save as WAV. The file has the frequency, wave and volume you set, so what you save is what you heard. It is a 48 kHz, 16-bit, one-channel WAV, which every audio editor, video editor and music app can open. The first and last hundredth of a second fade in and out, so the file starts and stops without a click.
The name says what is inside, for example tone-440hz-sine-5s.wav. A one-minute WAV is under 6 MB. If you need it smaller, turn it into an MP3 with WAV to MP3. To put a tone under a video, for a countdown beep or a test clip, use add audio to a video.
The saved WAV is made on your device in a moment, without any upload. Raise the volume above 0% first: a silent file would be no use, so the button waits until there is something to save.
Look after your ears and your speakers
A steady tone is more tiring to listen to than music, and very high or very low tones can be loud even when they seem faint. A few habits keep this hz generator safe to use.
- Start with your device volume low, and raise it a little at a time.
- Take headphones off before you change to a much higher or lower tone, then put them back on.
- Keep sessions short, and stop if you feel any discomfort or ringing in your ears.
- Go gently with very low tones on small or laptop speakers: they cannot play them well and can buzz or rattle.
Nothing you play here is recorded or sent anywhere, and the page keeps nothing once you close it. Read our privacy page for what the site itself keeps.
Play your tone
Set a frequency, pick a wave and press Play above, starting quietly. When you need the sound as a file, save it as a WAV in one click. More ways to work with sound are in the audio tools.