A voice memo, a lecture or a podcast episode can come out so quiet that even a phone at full volume barely helps. Turning up the speaker only changes how you play it. To fix it for good, you need to make audio louder in the file itself, so it plays louder wherever you open it.
That is what this volume booster MP3 tool does: it gives you a louder MP3, with nothing to install and no account. Drop an MP3 or another sound file, drag the level up to 400% and hear the boost before you save, or choose Safe level to amplify audio as far as it can go without cutting off the loudest parts. The file never leaves your computer.
How to increase MP3 volume in your browser
- Choose one or more sound files, or drop them anywhere on the page. The file opens with its waveform as the timeline and a Sound only card on the stage.
- Under Do, keep Adjust and drag Level, or tap one of the chips: Half, 1.5×, Double or Triple. The level starts at 200%.
- Press play (click the stage, or press the space bar) and listen. The preview plays at the level you picked, and the waveform redraws to match it.
- Under Save as, pick MP3 or WAV, then press Change volume.
- Save the new file, or press Save all as ZIP when you changed several.
Boosting a batch of recordings
Drop several files together and the button changes to match, for example Change volume of 3 files. In Adjust, every file gets the same level. In Safe level, each file is measured and lifted on its own, so each loudest point lands at about −1 dB unless a file is too quiet for the +20 dB limit. The numbers in the panel are for the first file.
Adjust: choose how much louder, and hear it first
Level runs from 25% to 400% in steps of 5%. 100% is the file as it is, so anything above it is a boost and anything below it turns the sound down. At exactly 100% there is nothing to change, and the panel asks you to pick another volume. Next to the percentage you see the change in decibels (dB), so 200% reads as +6.0 dB.
| Chip or level | Change | What it suits |
|---|---|---|
| 25% (lowest) | −12.0 dB | A recording that is far too loud next to your other files |
| Half (50%) | −6.0 dB | A track that drowns out the rest of a playlist |
| 1.5× (150%) | +3.5 dB | A gentle lift for speech that is only a little soft |
| Double (200%) | +6.0 dB | A typical quiet voice memo or phone recording; where the slider starts |
| Triple (300%) | +9.5 dB | Very quiet recordings with lots of room below the maximum |
| 400% (highest) | +12.0 dB | The faintest files, such as a lecture taped from the back row |
When the loudest parts turn red
Every digital recording has a ceiling: the loudest level a file can hold. A boost lifts everything, peaks included, and any peak pushed past that ceiling is cut flat (clipped). Clipping is heard as crackle or harshness on shouts, laughter and drum hits.
You do not have to find it by ear. Once the panel has read the sound, the parts that would go past the maximum turn red on the waveform, and a warning says they will be cut flat and may sound harsh. Lower the level until the red goes, or switch to Safe level. One short red click in an hour of speech is often hard to notice, so listen to that spot before you decide.
Safe level: amplify audio without clipping
Safe level is the hands-off choice. It finds the single loudest point in your file and lifts the whole recording so that point sits at −1 dB, just below the maximum. Everything rises by the same amount, so nothing is clipped and the balance between quiet and loud parts stays as it was.
Before you press Change volume, the panel shows three numbers: Loudest point now, After and Change. A soft phone recording might read −14.0 dB now, −1.0 dB after, and a change of +13.0 dB.
- A very quiet file is lifted by at most +20 dB, which is more than the 400% the slider allows. If even that cannot reach −1 dB, the panel says so and shows where the loudest point will end instead.
- A file already at a safe level changes little or nothing, and the panel suggests Adjust if you want it louder anyway.
One limit is worth knowing. Because Safe level looks at a single point, one loud bump, cough or door slam can hold the whole file back. If that spike sits at the start or the end, cut it off with Trim audio first. If it sits in the middle, Adjust at a higher level may give a louder result, at the cost of clipping that one moment.
Safe level is not loudness matching: a busy song and a sparse voice note lifted to the same peak can still sound different. For the sound inside a video, the same lift is on Normalise video audio.
Saving a louder MP3 or a WAV
Under Save as there are two tiles, each showing the size your file will be. MP3 (Plays everywhere) suits phones, chats and car stereos. WAV (Every sample kept) suits a file you plan to keep editing. A WAV you bring in starts as WAV, and every other file starts as MP3. The last line of the panel spells it out, for example MP3, 192 kbps or WAV, 16-bit.
An MP3 is saved at about the bitrate it already had (the nearest standard rate at or above it), so a 128 kbps podcast does not grow into a 320 kbps file. Any other file becomes a 192 kbps MP3, and a WAV is saved at 16-bit. Under 32 kHz an MP3 tops out at 160 kbps.
Changing the volume writes the sound out again, so an MP3 goes through one more round of compression. The loss is very small, but if you will edit again after the boost, save a WAV in between and make the MP3 last.
- Above 100%: song.mp3 is saved as song_louder.mp3.
- Below 100%: it is saved as song_quieter.mp3.
- Safe level: it is saved as song_normalised.mp3. Saved as WAV, each name ends in .wav instead.
Private, free, and what to try next
The whole job runs in your browser tab. The file is read from your device, the new copy is written on your device, and nothing is uploaded, which matters for a private call or an unreleased song. Our privacy policy explains what the site does collect.
Most files have no size limit. Some kinds, such as WMA or AIFF, take longer and can be up to 2 GB. It is free, with no account and no watermark, and it is not counted in the free daily limit, which is for document conversions only. It works in current Chrome, Edge and Firefox.
If the louder file is too big to send, Compress audio makes it smaller. If the quiet sound is part of a video, Change video volume does the same job and keeps the picture. The other sound editors are listed under audio tools.
Make your recording louder now
A recording that is too quiet is easy to fix once the file itself is louder. Choose your file above, drag Level and listen, or pick Safe level and let it find the highest safe lift, then press Change volume. Make your audio louder in moments, and keep the file on your own device the whole time.